LED Guardrail Light installation steps:

     Step one: first LED guardrail lights installed on the wall: the hole in the wall, install expansion screws, and then install LED guardrail lamps, with self-tapping screw lock; the distance between the barrier lamp according to customer's requirements set ; generally between 1CM to 3CM.
     Step Two: Then LED guardrail light signal lines, power lines docking up, signal lines are generally four-or five-pin plug of the male and female; the power line is the male and female 2-pin plug;
     Step Three: Install Power Supply (transformer or a switching power supply);
According to the power transformer as well as the power to calculate the barrier lamp transformers can show how many of each guardrail lamps; such as 108 light LED colorful guardrail lamp is 10W / M; 144 light LED guardrail lamp is 12W / M; if one uses a 400W waterproof transformer, you can take 108 light 36M tube; 144 while light with a 32 M tube. If the transformer can take 36M tube; transformer is placed in the middle of the first 18 and 19, followed two lines out, on each side with a 18.
Notes: 1. Transformer is generally used in 80% to 90% of the power;
2. No matter how great the power transformer, then each side of the tube is best not to exceed 25M; because the power supply wires are power loss; more to the back of the lower brightness LED guardrail lamps;
     The fourth step: LED guardrail lamp controller installation;
First load sub-controllers, directly to the sub-controller connected to the LED guardrail lamp;
Signals received signal (5-pin male and female plug), the power then power (2-pin male and female plug); and then will be the signal controllers and master docking, if the sub-master control and the distance will be far can be ultra-5 class network cable connected, so that the signal is better; each sub-zone control only a fixed number of LED digital tubes can generally be taken to 100M; to do floor body contour, each with a sub-control the way; specific situations according to LED Effects Fig installation (the manufacturer will help you count how many points a good control, each sub-band control path which normally will install the drawings). Points between the control and the master has also adopted the ultra-5 cable network cable connection; network cable is eight lines, using male and female plug and cable signals docking is received on the sub-control; different digital control loop between the need to disconnect the signal line.
     Step five: electricity, telecommunications numbers.
All received a 220V transformer main power supply, and then use an air switch and time switch;
Control of LED Digital Tube (LED fence light) Unified power; and then master on the plug inserted in the power supply 220V.
     Sixth Step: System Debug
Controller and LED Digital Tube (LED fence light) after power; may be part of the tube does not move, or the individual tube can not be normal
       Operation; the bad LED guardrail lamps removed and put back-up tube, until the normal operation.

Notes: 1. If the LED digital tube can not follow the normal procedure, to confirm whether the signal line of this pipe there is a problem please send the operation of the tube can not be replaced, if returned to normal, on the confirmation of this management problem, if not work you can try from another sub-control if not resolve installation problems please contact the manufacturer.
     2. Because LED guardrail lamps for electronic products, there are always some bad products, there will be lack of weld is like a cold solder joint; another waterproofing treatment is a very crucial factor, we recommend purchasing a good grasp of the quality of products; if it bad when you return the goods factory repair.
     3. Monochromatic light barrier or the installation of internal control is relatively simple, direct access on the corresponding line of the power; would also like to mention here is that the internal control number LED guardrail light installation: the installation of internal control number guardrail lamp tube in the order must be 1 1 installation; If you do not install the final order will appear as a whole are not synchronized.
     4. LED guardrail light, LED guardrail light is usually installed on the body to the floor, the installation costs are high, with a certain degree of risk; if there are broken pipes and in need of arms and legs hanging shelves or racks to replace them; it is proposed that the selection of quality products , and reduced maintenance costs.
Welcomed the Advisory related technologies!